When the temperature drops on a job site, the first instinct for some is to grab the nearest, warmest hoodie and throw it under your Flame-Resistant (FR) jacket. It seems like the most logical move for comfort, but in the world of high-voltage utilities and manufacturing, it’s a gamble that could turn a survivable incident into a life-altering injury.
Layering for protection isn't just about "more fabric." It’s a precision science where the space between your clothes is just as important as the clothes themselves.
There is a dangerous misconception that as long as your outer layer is FR-rated, what you wear underneath doesn't matter. This logic suggests that the outer shell acts as an impenetrable shield.
The reality? Heat transfers. During an arc flash or flash fire, an FR outer shell prevents the garment from igniting and continuing to burn, but it still gets incredibly hot.
If you are wearing a standard polyester or nylon "moisture-wicking" gym shirt or a synthetic-blend hoodie underneath:
The Melting Point: Synthetics melt at relatively low temperatures (around 250°C to 300°C).
The Shrink-Wrap Effect: The intense heat of an arc flash can cause those underlying synthetic fibers to melt and fuse directly to your skin.
The Trauma: Long after the fire is out, that plastic remains embedded in the dermal layer, leading to severe infection risks and agonizing debridement procedures.
The Rule of Thumb: If it’s not FR, it shouldn't be under your FR. Stick to 100% natural fibers (like cotton) in a pinch, but for true protection, FR-on-FR is the only way to go.
In the world of safety ratings, we talk a lot about ATPV (Arc Thermal Performance Value). You might assume that if you wear a 4-cal shirt and an 8-cal jacket, you have 12 calories of protection.
Actually, you often have more.
This is due to the Air Gap. When you layer two FR garments, a thin layer of air is trapped between them. Air is a poor conductor of heat and a fantastic insulator. This "dead air" creates a thermal buffer that significantly increases the total system arc rating beyond the simple sum of the individual parts.
Thermal Barrier: It slows the rate of heat transfer to the skin.
Expansion: Under extreme heat, the air gap can expand, creating even more distance between the heat source and your body.
Moisture Management: A proper FR layering system (like an FR base layer plus an FR fleece) manages sweat better than a single heavy coat, keeping the "insulating air" dry and effective.
Staying warm and staying compliant require a deep dive into the standards that govern our industry. As we transition through seasons, "layering up" must be documented and tested.
This standard requires that the entire system of clothing be rated for the potential incident energy of the task. If your job requires a Category 2 rating (8 cal/cm²), you cannot simply guess that two shirts equal 8 cals. You should look for "layered data" provided by manufacturers that proves the combination meets the threshold.
Important: In order to create a layering system the garments must be tested together for a combined arc rating which is why most layering systems remain in the same brand/manufacturer.
For those in oil, gas, or chemical manufacturing, NFPA 2112 ensures the garment won't melt, drip, or continue to burn. While this usually applies to the outer layer, wearing non-compliant layers underneath can still lead to "steam burns" if those layers hold moisture or "contact burns" if they melt.
|
Feature
|
NFPA 70E
|
NFPA 2112
|
|
Primary Risk
|
Arc Flash (Electrical)
|
Flash Fire (Chemical/Gas)
|
|
Measurement
|
ATPV / Ebt (Calories)
|
Percent Body Burn
|
|
Layering Focus
|
Total System Rating
|
Non-Melting Under-layers
|
To master the science of the air gap, follow these three steps:
Base Layer: Start with an FR-rated moisture-wicking tee. No synthetics.
Mid Layer: Add an FR hoodie or fleece. This creates the first critical "air gap."
Outer Shell: Use an FR jacket or parka for wind and water resistance.
Verify: Ensure your company’s safety officer has approved the "system rating" for the combination you are wearing.
Don't let a "comfortable" non-FR hoodie be the reason a survivable spark becomes a permanent injury. Respect the air gap, and keep the synthetics at the gym.
goSafe offers a wide variety of Seasonal PPE that is customizable on-site by our Customization Department. Our wide selection of FR Outerwear along with our huge variety of Cold Condition Gloves ensures that you'll be equipped to ward off the cold - and still get the job done safely. We also maintain a constant, ready-to-ship supply of FR Clothing and Safety Footwear in our 'Core FR' department. For more information on these products or any of our other safety and PPE products, please contact us at sales@gosafe.com.
At goSafe, Safety is our ONLY focus - and we'll partner with you to keep you and your teams safe. We're small enough to handle your local projects, yet large enough to serve national accounts. If safety is your mission, it starts with us.
Watch the video below for more information about goSafe's capabilities.